Product Description

Armour bridge deck waterproofing membrane protection board

Waterproofing Membrane for Bridge:UMS-Bridge Waterproof Paint are widely used in pedestrian bridge, overpass bridge, viaduct, highway bridge, sea bridge, cross river bridge, railway subgrade, subway, tunnel, reservoir, dam, fountain, artificial lake and other areas of waterproof protection.Waterproofing Membrane for Bridge Decks,Waterproofing Membranes for Concrete Bridge Decks.

Features of Waterproof Paint

1. Color: Green, Blue, Customized.

2. Excellent water-resistance and can be used for long-term immersion environment.

3. Color paint, visible waterproof effect.

4. Apply directly in wet substrate.

5. Firmly attach to the substrate, high bonding strength.

6. The Bridge Waterproof Paint will permeate the substrate to block up all the micropores on the purpose of avoiding leakage.

7. Excellent flexibility performance against slight architect vibration or small splits caused by different reasons.

8. Non-toxic and anti-volatility.

Solutions Recommend:

bridge deck waterproofing membrane systems-Solution 1

NO.	Name of products or Process	Layers	Dry film thickness(um)
1	Concrete surface treatment
2	KH-7 Concrete special primer	1	50
3	T100 Polyurea waterproof paint	1	600-2000
4	Paving asphalt or concrete as a protective layer
Total		2	650-2050

bridge deck waterproofing membrane systems-Solution 2

NO.	Name of products or Process	Layers	Dry film thickness(um)
1	Concrete surface treatment
2	KH-7 Concrete special primer	1	50
3	T100 Polyurea waterproof paint	1	600-2000
4	T200 Polyurea waterproof paint ( Outdoor naked selection)	1	100-200
Total		3	750-2250

Application

Concrete, brick and mortar wall surface and floor. Waterproof Paint For Basement and Bridge Waterproof Paint. Foundation of building, tunnel, Kitchen, Waterproof Paint For Bathroom.

How to use Waterproof Paint For Concrete

1) Mix the powder material with the liquid material proportionately (The ratio of power material to liquid material is 25:17 by weight), then fully stir for 3-5 minutes until it become uniform jelly staff with no obvious particles and sediments. It would be quite appreciated if the mixture could be laid aside for a while before stirring.

2) Brushing on the substrate directly and completely. 2-3 coatings in total are preferred according to real application condition. Brush repeatedly to ventilate the gas if any bubble is formed when brushing. The thickness of each coating should be 0.5mm

3) Re-coating (second coating) should be applied only after the surface dry of the first coating ( touch dry , it will take 1-2 hrs at normal temperature of 25-30℃), the direction of brushing should be vertical to the previous coating. Moisturize the previous coat by spraying mist on it if it is solidified before second coating.

Attention

1) Maintenance: Spraying mist on the final dry coating will achieve a better painting effect.

2) Ventilation equipment should be applied to speed the dry up of the coating when the application areas are damp or stuffy, such as sealing the drinking water pool or basement.

3)The paint should be applied at the temperature of 5-40℃, and avoid application in the rainy open air.

4)Substrate should be firm, clean without dirt, oil stains and any other impurities. Any holes, cracks on the surface of the substrate should be pre-sealed by grouting mortar.

5)Moisturize the substrate before the paint application but make sure no obvious droplet on it.

Contact us if you need more details on Waterproofing Membrane for Bridge. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Waterproofing Membrane for Bridge Decks、Waterproofing Membranes for Concrete Bridge Decks. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Polyurea Waterproof Coating